Hose Ramps & Cable Protectors

9mm Cable Protector in yellow - 10m roll
£81.20

9mm Cable Protector in yellow - 10m roll

£81.20

The 10060032 Cable Protector is a 10m long cable protector in bright yellow PVC capable of holding cables up 9mm in diameter. It can be cut either across the top or underneath to gain access to the cables. Dimensions: 80 x 16 x 10000 mm ..

Cable Protector 40mm x 12mm Channel
£10.21

Cable Protector 40mm x 12mm Channel

£10.21

The 10060026 Cable Protector is a 1m long, drop over type, cable protector in bright yellow designed for pedestrian traffic. They link together, end to end, with integral male/female connectors. Cable slot underneath: 40 x 12mm Dimensions: 135 x 20 x 1000 mm ..

Cable Protector for 20mm Max Diameter Cable 9M Length
£59.54

Cable Protector for 20mm Max Diameter Cable 9M Length

£59.54

The 10060018 Cable Protector is a 9m long cable protector in hard black rubber. Access to the cable is through a slot running the length of the cable protector. The largest cable it holds is 20mm in diameter. Dimensions: 100 x 30 x 9000 mm ..

Cable protector for 40mm Max Diameter Cable 4M Length
£65.20

Cable protector for 40mm Max Diameter Cable 4M Length

£65.20

The 10060019 Cable Protector is a 4m long cable protector in hard black rubber. Access to the cable is through a slot running the length of the cable protector. The largest cable it holds is 40mm in diameter. Dimensions: 165 x 55 x 4000 mm   ..

Cable Protector with 9mm x 26mm Slot - Grey PVC 9M Length
£65.20

Cable Protector with 9mm x 26mm Slot - Grey PVC 9M Length

£65.20

The 10060020 Cable Protector is a 9m long cable protector in grey PVC capable of holding cables up 9mm in diameter. It can be cut either across the top or underneath to gain access to the cables. Dimensions: 80 x 15 x 9000 mm ..

Cable Protector 100mm x 30mm Channel
£20.13

Cable Protector 100mm x 30mm Channel

£20.13

The 10060027 Cable Protector is a 1m long, drop over type, cable protector in bright yellow designed for pedestrian traffic. They link together, end to end, with integral male/female connectors. Cable channel underneath: 100 x 30mm Dimensions: 275 x 40 x 1000 mm ..

2 Channel Hose Ramp / Cable Protector with lid
£31.18

2 Channel Hose Ramp / Cable Protector with lid

£31.18

The 10060025 Hose and Cable Ramp protects two separate 32mm diameter cables/hoses. The bright yellow hinged lid is highly visible and allows easy access. They link together with integral male/female connectors. Max loading: 12 Tonnes per single wheel axle. 2 Channels: 32mm base x 34mm high Dimensions: 250 x 50 x 1000 mm BACK IN STOCK   ..

2 Channel Hose Ramp / Cable Protector for 84mm Dia Hoses/Cables with lid
£83.35

2 Channel Hose Ramp / Cable Protector for 84mm Dia Hoses/Cables with lid

£83.35

Moulded black rubber 2 channel hose ramp / cable protector with hinged solid yellow plastic lid. The ramps are deployed first and the cables placed inside once the ramps are in place. These ramps can accommodate up to 84mm diameter hoses or electrical cables and are ideal for concert venues, exhibitions and outdoor events where large diameter cables are often found. This product has been tested to withstand the maximum vehicle weight permitted on UK and EU roads.  Weight: 26 kg Max load: 44 Tonnes Channels: 84mm width (base), 92mm width (top), 80mm height Dimensions: 900 x 615 x 100 mm ..

3 Channel Cable Protector / Hose Ramp with Plastic Cover
£62.95

3 Channel Cable Protector / Hose Ramp with Plastic Cover

£62.95

BACK IN STOCK The 10060002 Hose and cable ramp is a 3 channel lidded ramp for pedestrians and vehicles. Each 970mm unit clicks together to make a continuous run. Cables/hoses can be added or removed once the ramps have been deployed. The lids are made from high visibility yellow PE. Outer Channels: 70mm wide x 50mm deep Inner Channel: 55mm wide x 50mm deep Dimensions: 970 x 590 x 80 mm Max Load: 44 Tonnes ..

3 Channel End Moulding (Twin Pack - Male & Female)
£21.26

3 Channel End Moulding (Twin Pack - Male & Female)

£21.26

The 10060003 Hose and Cable Ramp is a 3 channel end connector for the 10060002 Hose and Cable Ramp. This part is sold as a pair, one male and one female fitting.This part has no lid. Max Load: 44 Tonnes when joined to A224 Outer Channels: 70mm wide x 50mm deep Inner Channel: 55mm wide x 50mm deep Dimensions: (Male fitting) 150  x 590 x 80 mm : (Female fitting) 200  x 590 x 80 mm ..

5 Channel Cable Protector / Hose Ramp with Plastic Cover
£62.95

5 Channel Cable Protector / Hose Ramp with Plastic Cover

£62.95

The 10060001 Hose and cable ramp is a 5 channel lidded ramp for pedestrians and vehicles. Each 960mm unit clicks together to make a continuous run. Cables/hoses can be added or removed once the ramps have been deployed. The lids are made from high visibility yellow PE. Channels: 50mm deep x 35mm wide Dimensions: 960 x 590 x 80 mm Max Load: 44 Tonnes ..

2 Channel Hose Ramp / Cable Protector - Suits Fire Brigade 2.5 inch lay flat hose
£40.18

2 Channel Hose Ramp / Cable Protector - Suits Fire Brigade 2.5 inch lay flat hose

£40.18

The 10060005 Hose and Cable Ramp is the original moulded rubber hose ramp designed for Fire Brigade's 2.5" lay-flat hose. An inexpensive product that has been around for many decades. The part has two open top channels. Each channel is 85mm at the base opening up to 92mm at the top. The depth of each channel is 70mm. Each face of the ramp has three yellow visibility strips embedded into slots. The ramp is supplied with 2 connecting connectors fitted. Spares are available if required. Max Load: 44 Tonnes Dimensions: 850 x 300 x 84 mm ..

2 Channel Hose Ramp / Cable Protector
£43.17

2 Channel Hose Ramp / Cable Protector

£43.17

The 10060006 Hose and Cable Ramp is a moulded rubber hose ramp designed to protect 2 x 100mm diameter hoses. The part has two open top channels. Each channel is 95mm at the base opening up to 102mm at the top. The depth of each channel is 94mm. Each face of the ramp has three yellow visibility strips embedded into slots. The ramp is supplied with 2 connecting connectors fitted. Spares are available if required. Max Load: 44 Tonnes Dimensions: 820 x 310 x 102 mm ..

2 Channel Hose Ramp / Cable Protector
£56.55

2 Channel Hose Ramp / Cable Protector

£56.55

The 10060007 Hose and Cable Ramp is a moulded rubber hose ramp designed to protect 2 x 125mm diameter hoses. The part has two open top channels. Each channel is 135mm at the base opening up to 140mm at the top. The depth of each channel is 120mm. Each face of the ramp has three yellow visibility strips embedded into slots. The ramp is supplied with 2 connecting connectors fitted. Spares are available if required. Max Load: 44 Tonnes Dimensions: 980 x 290 x 135 mm ..

Ramp Section - Extendable Hose Ramp - 100mm hose/cable
£37.21

Ramp Section - Extendable Hose Ramp - 100mm hose/cable

£37.21

The 10060012 Hose and Cable Ramp is the ramp portion of a modular system that allows for many hoses and cables to be protected. The central section of this system is 10060011. The part has one open top channel. The channel is 108mm at the base opening up to 115mm at the top. The depth of each channel is 110mm. Each part can be joined to another to make a ramp for an infinite number of cables.If required 2 pieces of 10060012 can be fitted together to make a ramp suitable for 2 x 100mm hose or cable, when packing these away it is possible to split the ramp and store face to face to take up less space than a standard hose ramp. Max Load: 44 Tonnes Dimensions: 535 x 295 x 118 mm *Please note, this price is for ONE ramp section as shown in the main picture.  The other pictures show example configurations when used in conjunction with other products in the range. ..

Ramp Section - Extendable Hose Ramp - 125mm hose/cable
£48.87

Ramp Section - Extendable Hose Ramp - 125mm hose/cable

£48.87

The 10060036 Hose and Cable Ramp is the ramp portion of a modular system that allows for many hoses and cables to be protected. The central section of this system is 10060037. The part has one open top channel. The channel is 125mm at the base and 135mm at the top. The depth of each channel is 125mm. Each part can be joined to another to make a ramp for an infinite number of cables.If required 2 pieces of 10060036 can be fitted together to make a ramp suitable for 2 x 125mm hose or cable, when packing these away it is possible to split the ramp and store face to face to take up less space than a standard hose ramp. Max Load: 44 Tonnes Dimensions: 550 x 300 x 135 mm *Please note, this price is for ONE ramp section as shown in the main picture.  The other pictures show example configurations when used in conjunction with other products in the range. ..

Joiner Section - Extendable Hose Ramp - 100mm hose/cable
£21.14

Joiner Section - Extendable Hose Ramp - 100mm hose/cable

£21.14

The 10060011 Hose and Cable Ramp is the central portion of a modular system that allows for many hoses and cables to be protected. The ramp section of this system is 10060012. This part has one open top channel. The channel is 108mm at the base opening up to 115mm at the top. The depth of each channel is 110mm. Each part can be joined to another to make a ramp for an infinite number of cables, see 10060012. Max Load: 44 Tonnes Dimensions: 290 x 295 x 118 mm   ..

Joiner Section - Extendable Hose Ramp - 125mm hose/cable
£31.63

Joiner Section - Extendable Hose Ramp - 125mm hose/cable

£31.63

The 10060037Hose and Cable Ramp is the central portion of a modular system that allows for many hoses and cables to be protected. The ramp section of this system is 10060036. This part has one open top channel. The channel is 125mm at the base and 135mm at the top. The depth of each channel is 125mm. Each part can be joined to another to make a ramp for an infinite number of cables, see 10060036. Max Load: 44 Tonnes Dimensions:  320 x 300 x 135 mm   ..

2 Channel Hose Ramp / Cable Protector Steel Reinforced
£77.40

2 Channel Hose Ramp / Cable Protector Steel Reinforced

£77.40

The 10060014 Hose and Cable Ramp is a steel reinforced hose ramp. It is ideal for protecting hoses and cables up to 100mm in diameter. It has integrally moulded handles at both ends and can be easily deployed by one person. It has three high visibility strips and two red reflective cats eyes embedded into each ramp face. Max Load: 44 Tonnes Channels: 100 x 100mm Dimensions: 840 x 300 x 125 mm ..

Pedestrian 2 Channel Hose Ramp - fibre reinforced
£69.95

Pedestrian 2 Channel Hose Ramp - fibre reinforced

£69.95

The 10060013 Hose and Cable Ramp is a fibre reinforced pedestrian hose ramp. It is ideal for protecting hoses and cables up to 100mm in diameter. It has integrally moulded handles at both ends and can be easily deployed by one person. It has three high visibility strips and two red reflective cats eyes embedded into each ramp face. Max Load: 1000 kg Channels: 100 x 100mm Dimensions: 840 x 300 x 125 mm ..

Ramp Section - Modular Hose Ramp / Cable Protector
£44.65

Ramp Section - Modular Hose Ramp / Cable Protector

£44.65

The 10060008 Hose and Cable Ramp is the rubber wedge section for the modular ramp system designed to take larger diameter hose from 140mm up to a maximum of 180mm in diameter depending upon which steel bridge section is used. This particular part takes the vehicle up 160mm above the ground. Used with other rubber elements of this system it is possible to make a ramp 3400mm long which enables most cars to traverse the ramp without "beaching". The design allows for the front wheel to still be up in the rubber blocks when the rear wheel starts up the leading edge of the ramp. Max Load: 44 Tonnes Dimensions: 540 x 400 x 160 mm (max) ..

Ramp Section Extra long - Modular Hose Ramp / Cable Ramp
£140.00

Ramp Section Extra long - Modular Hose Ramp / Cable Ramp

£140.00

The 10060034 Hose and Cable Ramp is the rubber wedge section for the modular ramp system designed to take larger diameter hose from 140mm up to a maximum of 180mm in diameter depending upon which steel bridge section is used. This particular part takes the vehicle up 155mm above the ground. Used with other rubber elements of this system it is possible to make a ramp over 3750mm long which enables most cars to traverse the ramp without "beaching". The design allows for the front wheel to still be up in the rubber blocks when the rear wheel starts up the leading edge of the ramp. This part is similar to the 10060012 but has a 1200mm length for a more gentle incline. ..

Bridge Section - Modular Hose Ramp / Cable Protector
£110.14

Bridge Section - Modular Hose Ramp / Cable Protector

£110.14

The 10060009 Hose and Cable Ramp is the central steel bridge for the modular ramp system designed to take larger diameter hose up to a maximum of 140mm diameter. This particular steel bridge can accommodate 3 x 140mm dia hoses/cables. Using the rubber elements of this system it is possible to make a ramp 3400mm long which enables most cars to traverse the ramp without "beaching". The design allows for the front wheel to still be up on the rubber blocks when the rear wheel starts up the leading edge of the ramp. Max Load: 44 Tonnes Channels: 140-145mm width x 150mm depth Dimensions: 450 x 400 x 170 mm ..

Bridge Section Extra Height - Modular Hose Ramp / Cable Ramp
£104.90

Bridge Section Extra Height - Modular Hose Ramp / Cable Ramp

£104.90

The 10060017 Hose and Cable Ramp is the central steel bridge for the modular ramp system designed to take larger diameter hose up to a maximum of 170mm diameter. This particular steel bridge can accommodate 2 x 170mm dia hoses/cables. Using the rubber elements of this system it is possible to make a ramp 3400mm long which enables most cars to traverse the ramp without "beaching". The design allows for the front wheel to still be up in the rubber blocks when the rear wheel starts up the leading edge of the ramp. The steel is galvanised with yellow powdercoat over. Max Load: 44 Tonnes Channels: 170mm width x 170mm depth Dimensions: 360 x 400 x 175 mm ..

Bridge Section Extra Height - Modular Hose Ramp / Cable Ramp
£104.90

Bridge Section Extra Height - Modular Hose Ramp / Cable Ramp

£104.90

The 10060033 Hose and Cable Ramp is the central steel bridge for the modular ramp system designed to take larger diameter hose up to a maximum of 185mm diameter. This particular steel bridge can accommodate 2 x 185mm dia hoses/cables. Using the rubber elements of this system it is possible to make a ramp 3400mm long which enables most cars to traverse the ramp without "beaching". The design allows for the front wheel to still be up in the rubber blocks when the rear wheel starts up the leading edge of the ramp. This steel bridge has a galvanised finish with red powder coating over. Max Load: 44 Tonnes Channels: 185mm width x 185mm depth Dimensions: 370 x 400 x 190 mm ..

Joiner Section - Modular Hose Ramp / Cable Protector
£62.52

Joiner Section - Modular Hose Ramp / Cable Protector

£62.52

The 10060010 Hose and Cable Ramp is the rubber block section for the modular ramp system designed to take larger diameter hose from 140mm up to a maximum of 180mm in diameter depending upon which steel bridge section is used. This particular part keeps the vehicle up 160mm above the ground. Used with other rubber elements of this system it is possible to make a ramp 3400mm long which enables most cars to traverse the ramp without "beaching". The design allows for the front wheel to still be up on the rubber blocks when the rear wheel starts up the leading edge of the ramp. Max Load: 44 Tonnes Dimensions: 450 x 400 x 160 mm   ..

Joiner Section Extra Height - Modular Hose Ramp / Cable Protector
£41.11

Joiner Section Extra Height - Modular Hose Ramp / Cable Protector

£41.11

The 10060016 Hose and Cable Ramp is the rubber joining block section for the modular ramp system designed to join any of the steel bridge sections together so that multiple hose/cables can be covered. This part locks two steel bridge sections together by dropping over the two steel "pots" on each end of the steel bridge. If required this part enables any number of steel bridges to be joined. Max Load: 44 Tonnes Dimensions: 350 x 400 x 180 mm ..

Pedestrian Hose Ramp for Large Diameter Hoses
£272.24

Pedestrian Hose Ramp for Large Diameter Hoses

£272.24

This fantastic new pedestrian hose ramp has been specifically designed for tankering applications. The hose ramp could also be used to aid pedestrian movement during fuel drop offs. The central bridge section is produced from extruded aluminium and will take a 200mm max diameter hose (this allows for some expansion of 6inch slurry and waste hoses). The yellow ramps are produced from bright yellow GRP to provide a robust, lightweight and highly visible solution. The closed bridge section allows for positive positioning of the main hose and there is some room left for some smaller diameter jetting hoses too. The design brief was to create a product that could be deployed by one man quickly and be split into separate pieces for storage on road going tankers. The ramp comes in 3 separate sections and each piece weighs less than 15.0Kg which keeps each component within manual handling limits. The central aluminium bridge section weighs 9.5Kg and the GRP ramps each weigh approximately 13.0Kg so in total the whole assembly is less than 35.0Kg. The width, once assembled is 1000mm and the overall total length is 1850mm. The ramp can be quickly assembled each time the hoses or cables are deployed. Aluminium Tunnel: 225 wide x 200mm high Max Load: 200 kg Max Hose/Cable diameter: 200mm Dimensions: 2080 x 995 x 235 mm   ..

Pedestrian Hose Ramp with Solid Platform
£245.58

Pedestrian Hose Ramp with Solid Platform

£245.58

The 10060029 Hose and Cable Ramp is a pedestrian ramp designed to cover multiple hoses. It has a bridge distance of 800mm and a gap height of 100mm. It can accommodate up to eight 100mm hoses and is delivered ready assembled. The solid GRP top prevents problems with pedestrians with high heels. It requires two people to lift and deploy. See also 10060028.   Max load: 250kg Dimensions: 1560 x 880 x 125mm This item is shipped on a pallet due to its size. ..

Replacement Wedge - 880 x 375 x 125mm
£57.50

Replacement Wedge - 880 x 375 x 125mm

£57.50

The 10060035 is the rubber wedge element that fits with the GRP grating to make Hose & Cable Ramp 10060029 Dimensions: 880 x 375 x 125mm High ..

Steel Topped Heavy Duty Hose Ramp / Cable Protector
£116.09

Steel Topped Heavy Duty Hose Ramp / Cable Protector

£116.09

The 10060015 Hose and Cable Ramp is a steel topped hose ramp with a single channel. It is ideal for protecting hoses and cables up to 105mm in diameter. It has been independently tested and can withstand 80 Tonne vehicles crossing over. A larger version of this part is 10060031 Max Load: 80 Tonnes Channel: 105 x 200mm Dimensions: 810 x 290 x 120 mm ..

Steel Topped Heavy Duty Hose Ramp / Cable Protector
£285.65

Steel Topped Heavy Duty Hose Ramp / Cable Protector

£285.65

The 10060031 Hose and Cable Ramp is a steel topped hose ramp with a single channel. It is ideal for protecting hoses and cables up to 150mm in diameter. It has been independently tested and can withstand 80 Tonne vehicles crossing over. A smaller version of this part is 10060015 Max Load: 80 Tonnes Channel: 210 x 150mm Dimensions: 820 x 290 x 165mm ..

Dog Bone Connecting Set Including Screw & Washer
£2.42

Dog Bone Connecting Set Including Screw & Washer

£2.42

This connector is fitted to all relevant hose ramps before shipping but can be ordered separately to repair any ramps with lost or broken connectors. Screws and washers are supplied and included in the price. ..

Vulcascot - Snap Fit - Standard - 14mm x 8mm channel - 3m
£22.95

Vulcascot - Snap Fit - Standard - 14mm x 8mm channel - 3m

£22.95

Vulcascot’s comprehensive range of Snap Fit profiles is available in black , grey  or beige . Profiles are designed to house one or more cables in a variety of combinations depending on the application, allowing the user total flexibility to secure a wide permutation of lead and cable sizes. Each profile features a unique membrane located in the base for fast, easy fitting. simply snap open the membrane, push in the cables and lay the protector complete with cables in position, on the floor.  Snap Fit products are ideal for preventing tripping and falling over untidy, loose cables as well as protecting cables from damage. Without doubt this is the perfect solution for all round protection from danger in offices, shops, laboratories, exhibition halls, hospitals and schools.  Fire tested to BS 476 Part 7 Class 3 Halogen free (non carcinogenic) in the event of fire Low smoke, non toxic and low fume emission levels Tested for non conductivity to BS903-C5, 500V UV stabilised for extended outdoor life Latex free ideal for hospitals Easily reusable when needed   TYPE - VULCASCOT SNAP FIT STANDARD  Channel Size - 14mm x 8mm Overall Dimensions - 68mm x 11mm x 3000mm Please Note - Our Vulcascot products are delivered direct from the manufacturer. Orders placed before 12:30pm will normally be shipped the same day, for next day delivery.  Orders received after 12:30pm will be processed the following day.   ..

Vulcascot - Snap Fit - Standard - 14mm x 8mm channel - 9m
£64.95

Vulcascot - Snap Fit - Standard - 14mm x 8mm channel - 9m

£64.95

Vulcascot’s  comprehensive range of  Snap Fit  profiles is available in black, grey or beige. Profiles are designed to house one or more cables in a variety of combinations depending on the application, allowing the user total flexibility to secure a wide permutation of lead and cable sizes. Each profile features a unique membrane located in the base for fast, easy fitting. simply snap open the membrane, push in the cables and lay the protector complete with cables in position, on the floor.  Snap Fit products are ideal for preventing tripping and falling over untidy, loose cables as well as protecting cables from damage. Without doubt this is the perfect solution for all round protection from danger in offices, shops, laboratories, exhibition halls, hospitals and schools.  Fire tested to BS 476 Part 7 Class 3 Halogen free (non carcinogenic) in the event of fire Low smoke, non toxic and low fume emission levels Tested for non conductivity to BS903-C5, 500V UV stabilised for extended outdoor life Latex free ideal for hospitals Easily reusable when needed   TYPE - VULCASCOT SNAP FIT STANDARD  Channel Size - 14mm x 8mm Overall Dimensions - 68mm x 11mm x 9000mm Please Note - Our Vulcascot products are delivered direct from the manufacturer. Orders placed before 12:30pm will normally be shipped the same day, for next day delivery.  Orders received after 12:30pm will be processed the following day.       ..

Vulcascot - Snap Fit - Type B - 30mm x 10mm channel - 3m
£33.95

Vulcascot - Snap Fit - Type B - 30mm x 10mm channel - 3m

£33.95

Vulcascot’s comprehensive range of Snap Fit profiles is available in black, grey or beige. Profiles are designed to house one or more cables in a variety of combinations depending on the application, allowing the user total flexibility to secure a wide permutation of lead and cable sizes. Each profile features a unique membrane located in the base for fast, easy fitting. simply snap open the membrane, push in the cables and lay the protector complete with cables in position, on the floor. Snap Fit products are ideal for preventing tripping and falling over untidy, loose cables as well as protecting cables from damage. Without doubt this is the perfect solution for all round protection from danger in offices, shops, laboratories, exhibition halls, hospitals and schools. Fire tested to BS 476 Part 7 Class 3 Halogen free (non carcinogenic) in the event of fire Low smoke, non toxic and low fume emission levels Tested for non conductivity to BS903-C5, 500V UV stabilised for extended outdoor life Latex free ideal for hospitals Easily reusable when needed   TYPE - VULCASCOT SNAP FIT - TYPE B Channel Size - 30mm x 10mm Overall Dimensions - 82mm x 14mm x 3000mm Please Note - Our Vulcascot products are delivered direct from the manufacturer. Orders placed before 12:30pm will normally be shipped the same day, for next day delivery.  Orders received after 12:30pm will be processed the following day.   ..

Vulcascot - Snap Fit - Type B - 30mm x 10mm channel - 9m
£97.95

Vulcascot - Snap Fit - Type B - 30mm x 10mm channel - 9m

£97.95

Vulcascot’s comprehensive range of Snap Fit profiles is available in black, grey or beige. Profiles are designed to house one or more cables in a variety of combinations depending on the application, allowing the user total flexibility to secure a wide permutation of lead and cable sizes. Each profile features a unique membrane located in the base for fast, easy fitting. simply snap open the membrane, push in the cables and lay the protector complete with cables in position, on the floor. Snap Fit products are ideal for preventing tripping and falling over untidy, loose cables as well as protecting cables from damage. Without doubt this is the perfect solution for all round protection from danger in offices, shops, laboratories, exhibition halls, hospitals and schools. Fire tested to BS 476 Part 7 Class 3 Halogen free (non carcinogenic) in the event of fire Low smoke, non toxic and low fume emission levels Tested for non conductivity to BS903-C5, 500V UV stabilised for extended outdoor life Latex free ideal for hospitals Easily reusable when needed   TYPE - VULCASCOT SNAP FIT - TYPE B Channel Size - 30mm x 10mm Overall Dimensions - 82mm x 14mm x 9000mm Please Note - Our Vulcascot products are delivered direct from the manufacturer. Orders placed before 12:30pm will normally be shipped the same day, for next day delivery.  Orders received after 12:30pm will be processed the following day. ..

Vulcascot - Industrial - Type F - 23mm channel - 4.5m
£115.95

Vulcascot - Industrial - Type F - 23mm channel - 4.5m

£115.95

Vulcascot Industrial Snap Fit Cable Protector In many instances, cables found straggling across the floor of industrial locations are often forgotten but are still prone to damage. Tested for durability over many years of safe operation in warehouses, industrial units, building sites, hospitality events and exhibitions particularly where fork lift and pallet trucks are in constant operation, this robust range has no parallels. These tough profiles are designed to protect power cables and cable bundles from physical damage particularly in areas where there there is frequent vehicle movement. In computer and electrical control rooms where multiple cables need to be kept tidy as well as protected, these large profiles will safely house cables up to 60mm For added safety our flexible cable protectors are:- Fire tested to BS 476 Part 7 Class 3 Halogen free (non carcinogenic) in the event of fire Low smoke, non toxic and low fume emission levels Tested for non conductivity to BS903-C5, 500V UV stabilised for extended outdoor life Latex free ideal for hospitals Easily reusable when needed   TYPE - VULCASCOT INDUSTRIAL - TYPE F Channel Size - 23mm Overall Dimensions - 127mm x 28mm x 4500mm Please Note - Our Vulcascot products are delivered direct from the manufacturer. Orders placed before 12:30pm will normally be shipped the same day, for next day delivery.  Orders received after 12:30pm will be processed the following day. ..

Vulcascot - Industrial - Type FF - 2x23mm channel - 4.5m
£157.95

Vulcascot - Industrial - Type FF - 2x23mm channel - 4.5m

£157.95

Vulcascot Industrial Snap Fit Cable Protector In many instances, cables found straggling across the floor of industrial locations are often forgotten but are still prone to damage. Tested for durability over many years of safe operation in warehouses, industrial units, building sites, hospitality events and exhibitions particularly where fork lift and pallet trucks are in constant operation, this robust range has no parallels. These tough profiles are designed to protect power cables and cable bundles from physical damage particularly in areas where there there is frequent vehicle movement. In computer and electrical control rooms where multiple cables need to be kept tidy as well as protected, these large profiles will safely house cables up to 60mm For added safety our flexible cable protectors are:- Fire tested to BS 476 Part 7 Class 3 Halogen free (non carcinogenic) in the event of fire Low smoke, non toxic and low fume emission levels Tested for non conductivity to BS903-C5, 500V UV stabilised for extended outdoor life Latex free ideal for hospitals Easily reusable when needed   TYPE - VULCASCOT INDUSTRIAL - TYPE FF Channel Size - 2 x 23mm Overall Dimensions - 156mm x 30mm x 4500mm Please Note - Our Vulcascot products are delivered direct from the manufacturer. Orders placed before 12:30pm will normally be shipped the same day, for next day delivery.  Orders received after 12:30pm will be processed the following day. ..